LR1000 Mini Receiver Configuration Guide


This is the LR1000 Mini Receiver Configuration Guide

In this video I will show you how to setup the LR1000 (aka. FD1000) from the wiring, to the config, and binding as these little receivers bind a little differently to other receivers. The process will be very similar for ANY other receiver that uses SBUS. Shortly there will be a review, and I show you a little issue with some of the receivers, and the easy solution.


This is a comprehensive unboxing and review on the new FuriousFPV LR1000 Mini Receiver for FrSky controllers.
This is truly one of the best receivers for FrSky currently on the market both for price and its small size.
This receiver packs a huge punch with a 1Km operating range in a 1.4g package!
If you have any questions feel free to leave them below
. This receiver has full ground, 5Vin, S.Bus, Telemetry.
The antenna has a cover as well as an open clear end tubing.
This will need to be run off of a voltage regulator, for a review on a great 5v regulator from a great brand.



The LR1000 Mini Receiver range is one full kilometer. It is packed full of cool features.
It has a S-bus output without inverter, 8 channels of output (with a 9th channel dedicated to RSSI), a telemetry hub and full compatibility with FrSky Taranis, Taranis Plus, & XJT Module.
 
The LR1000 Mini Receiver for FrSky from Furious FPV and we figured there should be a configuration guide for this great receiver.
Anyhow, let’s get on with the useful information…


Binding the LR1000 Mini Receiver to the Frsky Taranis

  • On the Taranis, go to MODE SETUP (page 2) in the model configuration.
  • Go to Mode inside Internal RF and select D8.
  • Press and hold the receiver bind button and turn the receiver on (by plugging in your battery).
  • Release the button. A green LED light should light up on the receiver.
  • Going back to the Taranis; press BIND. The transmitter beeps, indicating it’s in bind mode.
  • Wait for the green LED on the receiver to turn off. The binding procedure has finished.
  • Exit the BIND mode in the Taranis.
  • Unplug the battery to turn off the receiver.

Binding the LR1000 Mini Receiver to the XJT module

  • Using the dip switches on the XJT module, select the D8 mode. They should be in the following position: switch 1 = ON, switch 2 = OFF.
  • Press and hold the receiver bind button and turn the receiver on (by plugging in your battery).
  • Release the button. A green LED light should light up on the receiver.
  • Press and hold the bind button and turn the transmitter on.
  • Release the button. A green light should blink on the module, indicating it’s in bind mode.
  • Wait for the green LED on the receiver to turn off. The binding procedure has finished.
  • Turn the transmitter off.
  • Unplug the battery to turn off the receiver.

Receiver Configuration in the Cleanflight configurator

  • In the PORTS PORTS tab, select the UART that corresponds to the receiver (usually UART3 in F3 flight controllers) and activate Serial RX.
  • Save by clicking on the Save and Reboot button.
  • In the CONFIGURATION tab, in the Receiver Mode section, select RX_SERIAL.
  • In the same tab, in the Serial Receiver Provider section, select SBUS.
  • Save by clicking on the Save and Reboot button.
  • Go to CLI and type the following commands:
    set sbus_inversion = OFF
    save
  • The FC will reboot, applying the change.
  • Go to the RECEIVER tab and make sure the receiver acts like it should.

Telemetry Configuration

  • In the PORTSPORTS tab, select the UART that corresponds to the telemetry (usually UART2 in F3 flight controllers) and select FrSky in Telemetry. Leave the baud rate on AUTO.
  • Go to CLI, and type the following commands:
    set telemetry_inversion = ON
    save
  • The FC will reboot, applying the change.
  • Make sure you’re getting the telemetry values in our Taranis correctly.

Connection Diagrams for Various Furious FPV FCs

 
123Go to Source




13total visits,11visits today

Leave a Reply

Your email address will not be published.